| |
 |
What are the distinguishing features of the OptiTrans lighting products compared with the traditional light? |
 |
Can be compared from several following aspects: |
| |
- Design . The design of the reflector is unique, thus improved all utilization ratio.
- Material . Most of the traditional light reflector is made of aluminum. The reflector of the OptiTrans lighting products is general is made of glass, the reflecting rate has reflected light after their have reflected light in the surfaces and all plated and climbed to a high place the membrane.
- Stability degree of the mere centre . Traditional light used the spiral lamp holder, it is very difficult to make the light in charge of center's keeping in the focus position, and the light of one pair of ends that the OptiTrans lighting products use double end lamp holder, has improved stability degree of all centre greatly.
- Light deficiency . The traditional light uses aluminum as covers of the reflector that oxidizing and turning to be yellow because the temperature of the bulb rises, so the reflecting rate decays fast. The OptiTrans lighting products uses membrane in glass, can keep the good mere output for a long time.
- Stable device . The traditional light is used inductance stable device which is unable to do constant voltage export, and output the voltage change as the voltage goes up and down, thus cause the life-span of the bulb to shorten. The OptiTrans lighting products uses electron stable device, under inputting the situation that the voltage range is 165V 265V, exporting 220V steadily, output power is invariable, the power factor is up to 0.98. In addition, inductance stable device losses 18%, the electron stable device of is only 7.5% 8%.
|
|
| |
|
| |
|
How to solve problem of light in charge of hot contact that produces ? |
|
The light above 250W all have a question contacted, because the high temperature makes the contact oxidize, causing the unable lighting point of a lamp and short life-span of light, we adopt the law of connecting of the wire type, in this way the light has not contacted clicking when in charge point so the stability has been improved, has lengthen the service life of the light. |
|
| |
|
| |
|
Are the company products the high-pressure sodium light or the low-voltage sodium light?
|
|
High-pressure sodium light. The Low-pressure sodium light is one that can be bought at present arrives the most effective products of giving out light.
the majority is used in the tunnel at present, because its light tube is too long, the design of the reflector is more difficult, and the cost of production will become higher, and also only some particular factories are capable production only at present, such as OSRAN, PHILIPS, and the cost is probably more than 8 times of the high-pressure sodium light, because there are few manufacturers , it is difficult to supply, this is that a low-voltage sodium light has been so the unable reason for turning the main product into all the time for many years. The high-pressure sodium light is more successful products, it is very easy too to purchase on the market, the manufacturer can work out easily even if it is a special specification.
|
| |
|
|
| |
|
What differences does the light tube have with nature products to in the selling market? And the Comparison of its advantages and disadvantages.
|
|
There are 2 kinds of lights that we used, sodium light is the high-pressure sodium light, it is the same in the sell market, we only utilize special optics to design and improve the luminance, and get the result of energy-conservation.
Mercury light, Metal halide light, Sodium light, these are all gas output electric light, each have different characteristics. With the present trend (energy-conserving and environment-protective factor), the mercury light will be eliminated gradually, because its efficiency is the lowest, it is worst to perform the color. Sodium light, because it to give out light most effective lighting product at present , but can only send out the decadent spectrum , it is extremely bad to perform the color, but used in the traffic and light and seldom stress and perform the color local result is very good. Metal halide light, is a future trend, it has good luminescence efficiency (70 110lm/w ), performing the color better than the mercury light and the sodium light. Will usually have level that Ra is greater than 70, and there are 2 kinds of color temperature available. (in the sell market products used in general illumination). Certainly other color temperature (6000K , 8000K ,etc. ) can be made too, the light of the special color can be produced too. |
|
| |
|
| |
|
Some want not only electricity watt to drop count, buy want towards yellow light (gentle light series), the high-pressure sodium light is too dazzling, whether this can improve?
|
|
Gentle light series, we also generally called warm color series, can get it with the Metal halide light of 3000K. The Low-pressure sodium light tube length is longer, is 10 times of the high-pressure sodium light, feel less dazzling, or what we called the Giddy Problem. In Sodium light and Metal halide light, we can , we can make use of the designs of the light and lanterns to reduce the giddiness, this is the principle which the light and lanterns designer and goal pursued at present too.
|
|
| |
|
| |
|
What are the reasons caused lights out? |
|
- Check the socket if insert
- The light tube is out of order
- Tthe stable device of electron is out of order
|
|
| |
|
| |
  |
 |
|
|
